MAGNFIX Magnetic License Plate Holder

No need to drill into your car's front bumper or damage its paint with adhesive pads! The MagNFix magnetic number plate holder offers a secure fitting for your number plates without causing damage to your car.

The MagNFix magnetic license plate holder contains a total of 20 magnets for one license plate. 10 magnets are attached to the inside of the bumper and 10 magnets to the back of the license plate so that the license plate has a firm hold even at high speeds.

Fastening instructions

Please be sure to follow the enclosed safety instructions!
Sticking the magnets on the license plate:
When sticking the magnets on the license plate, please make sure that the magnets
not in the embossing (aluminum license plate) or on the rivets (3D license plate)
to stick. The magnet must be stuck on a flat surface, otherwise
full adhesion cannot be achieved.

How To Fit Your MagNFix Magnetic License Plate Holder

1. Position magnets on the bumper inside and outside and
Test positioning. Absolutely on the mutual attraction of the
Pay attention to magnets!
2. Mark the position of the outer magnets on the license plate and the
Thoroughly clean/degrease the affected areas with the alcohol swab.
3. Remove the protective film from the magnets and stick it on the license plate. The
Press the magnets firmly onto the license plate.
4. Glue the license plate fleece onto the license plate, ideally on the
Start at the top of the license plate. License plate fleece only at the top
Stick it in place, then peel it off completely and spread it downward
stick on. (An air cushion around the magnets is desired and normal here)
5. Mark the position of the inner magnets on the bumper and the
Thoroughly clean/degrease the affected areas with the alcohol swab.
6. Remove the protective film from the magnets and stick it on the bumper. The
Press the magnets firmly onto the bumper.
7. Glue foil cuts to the magnets. For this purpose the foil on the magnet
Apply and then apply from top to bottom. Here too there is a
Air pocket around the magnet is normal. The magnets are through the foil
protected from incoming water and dirt.Finishing it off with pre-applied adhesive tape ensures a tight finish to the body line.

PRODUCT SPECIFICATION

• Suitable for aluminum and 3D license plates!
• Super strong hold: a set of MagNFix achieves a holding force of over 64kg, which is more than other magnets!
• No scratches in the paint thanks to the gentle Velcro over the magnet
• Super slim license plate holder: thickness only 3mm!

COMPATIBILITY

This license plate holder works with wide range of vehicles & number plate types. If you're unsure if it will fit your vehicle, please contact our friendly customer service team here.

WHAT'S IN THE BOX?

One set = holder for one license plate

• 10 pairs of magnets (20 magnets with opposite polarity):
• 10 magnets for the license plate
• 10 magnets for the bumper
• 1 Velcro in size 520 x 100 mm, can be cut to the license plate length
• 2 alcohol wipes for degreasing
• Matching pieces of foil to cover the magnets behind the bumper
• Safety and application instructions
• Assembly and fastening instructions

Unless explicitly stated otherwise, all products sold by R44 Performance Limited are designated RACE ONLY and are solely for competition or off-road use limited to racing formally sanctioned by a recognized racing organization. Any other use, including recreational off-road use, may violate local, state, and Federal laws. R44 Performance Limited does not implicitly or explicitly confirm the legality of using any products it sells on public roads; that is entirely the responsibility of the consumer.

It is the responsibility of the customer to check with all federal, state local and environmental laws before ordering and installing a product. R44 Performance Limited is not responsible for any fees, fines or costs that a customer may incur as a result of failing to check with federal, state, local or environmental laws before ordering and installing a product.

We get a large number of custom orders and requests everyday, so as a result it is not always possible for us to keep every item in stock at all times in our warehouse. If you require the item urgently please contact our sales team here to check the stock before you make your purchase.

We totally understand if you're not certain a part will be compatible with your car, so we highly recommend contacting us here with your query. Our friendly sales team will then be in touch to confirm if this part is the correct part you are looking for.

All in stock products ship the same day if ordered before 2pm GMT

For out of stock items we will contact you with an estimated wait time if not otherwise specified above.

We offer worldwide shipping on all products. If upon receiving your product you wish to return; we offer a 30-day returns policy. For our in-depth returns information please follow the link. "R44 Returns Policy

All of our products come with a standard warranty of 1-3 years. This is dependant on the type of product however. For more details please see our warranty page here.